Step Tutorial for Installing a Bathtub
Step Tutorial for Installing a Bathtub
Blog Article
Every person has their unique theory on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Mounting a bath tub isn't precisely rocket science, but it does need strong plumbing, carpentry, and sometimes, tiling skills. Replacing an old tub with a brand-new one is also a reasonably tough job. If the old bathtub is readily accessible, the task can relocate speedily; if you need to open a wall to get rid of the old bathtub and also position the new bath tub, the job is much harder. In either situation, the job is within a home handyman's skills, although you will certainly need an assistant to move out the old bathtub and also set in the brand-new one. Ensure you have qualified on your own for the job and are comfortable trying it. As opposed to employing a contractor to take over a halfway-completed task, it is much better to think about using one prior to you begin. Chances are you may need a professional plumber to make tube links.
This write-up will assist you mount a new tub in your shower room if you have currently purchased a new tub and also do not require to change the plan of your previous water supply pipelines.
Your tools as well as material list ought to comprise the following:
Getting ready for the Installation
Firstly, the supporting structure supplied with the bath must be fitted (if needed) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is essential to make sure that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the faucets unit to avoid pressure on the tub.
Fit the adaptable faucet ports to the bottom of both taps making use of 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you use every one of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom need to now prepare to be fitted in its last setting.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installation, after that the first thing you need to do is separate the water supply. After doing so, activate the faucets to drain any water remaining in the system. The process of getting rid of the existing taps can be rather bothersome due to the limited gain access to that is often the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the faucets. Have a towel all set for the staying water that will come from the pipes. When the supply pipelines have been removed, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from transforming throughout this procedure. Once the faucets have been eliminated, the holes in the bath/basin will have to be cleaned of any old sealing substance.
Before moving on to fit the new taps, compare the pipeline links on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Setting up the Bath tub
Utilizing both wooden boards under its feet, put the tub in the required placement. The wooden boards are helpful in evenly spreading out the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four small factors.
The following objective is to make sure that the tub is leveled all round. This can be accomplished by checking the level as well as changing the feet on the bath tub up until the level checks out level.
To install taps, fit all-time low of the outermost adaptable faucet port to the appropriate supply pipe by making a compression join; then do the exact same for the other faucet.
Turn on the water supply as well as check all joints as well as brand-new pipework for leaks as well as tighten them if necessary. Fill up the tub as well as also inspect the overflow outlet as well as the typical electrical outlet for leaks.
Finally, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and also securing around the bath tub should wait up until the bathtub has actually been made use of at least when as this will settle it right into its last setting.
Fitting New Touches
If the tails of the new faucets are plastic, then you will require a plastic connector to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the other end provides a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will need minimizing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the tap in the mounting opening in the bath/basin making sure that the washers are in area in between the tap and the sink. Secure the tap in place with the maker given backnut. Once the faucet is safely in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical faucet adapters. The previous kind must be connected to the faucet finishes first, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bath satisfies the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to split an inflexible seal, triggering the water to pass through the wall in between the bathroom and also the tiling, resulting in difficulties with moisture and also possible leaks to the ceiling below.
You can pick from a selection of coloured sealants to assimilate your components and also fittings. They are sold in tubes and also cartridges, and also are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with twists of soaked paper or soft rope. Remember to always fill up the bathtub with water prior to securing, to permit the motion experienced when the bathtub is in usage. The sealant can fracture fairly early if you do not take into account this motion prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally quickly offered on the market. It is suggested to fit the floor tiles utilizing waterproof or water resistant adhesive and cement.
How to Install a Freestanding Bathtub?
Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.
This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.
Slope
Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.
Placement
A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.
According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.
Clean the bathroom floor
After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.
Steps to Install a Freestanding Bathtub:
STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.
STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.
STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.
STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.
STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.
STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.
Tips to Maintain a Freestanding Bathtub:
Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter. Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches. Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains. Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris. Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run. If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.
I was guided to that article about Tools You Need to Install a New Bathtub through a good friend on a different web blog. Feel free to take the opportunity to promote this post if you enjoyed it. We value reading our article about Installing A Bathtub.
Contact Report this page